太空漫游 书
您好,歡迎訪問無錫合達電子設備有限公司官網!
0510-83212339
138-6181-2138
無錫合達電子設備有限公司
您的位置:首頁 > 新聞動態 > 行業知識
聯系我們

無錫合達電子設備有限公司

地址:無錫市惠山區恒新路3號
電話:138-6181-2138

咨詢熱線138-6181-2138

廠家介紹六大老化房的價格決定因素

發布時間:2018-12-15人氣:79

六大老化房的價格決定因素:老化房的常做溫度點:涉及到排風系統,根據老化房內產品的總功率(發熱功率),然后根據需要很定的溫度,通過相應的公式算出排風機的功率,排風管的大小。1: 老化房房間大小(房間大小決定風機選型,風機數量,風管大小)

Six determinants of the price of the aging house: the common temperature point of the aging house: involving the exhaust system, according to the total power (heating power) of the products in the aging room, and then according to the need for a very fixed temperature, the power of the exhaust fan and the size of the exhaust duct are calculated by the corresponding formula. 1: Room size of aging room (room size determines fan selection, number of fans, size of ducts) 通常市面有軸流風機、離心風機、風柜來制作

Usually there are axial flow fans, centrifugal fans and air cupboards on the market.

軸流風機安裝于老化房頂部,在天花上裝根據風機的數量裝相應的百葉窗口,采用上面出風上面回風的概念,此方法造價低廉,溫度均勻度可控性不高,因為熱氣是從下往上的

Axial flow fan is installed on the top of aging house, and the corresponding shutter window is installed on ceiling according to the number of fans. The concept of return air above the top outlet is adopted. This method is cheap and the temperature uniformity is not controllable because the hot air is from the bottom to the top.

離心風機安裝于老化房頂部,再根據風機的功率以及房間的大小設計相應的風管數量,每條風管連接至室內底部,在每條風管上安裝2個雙層百葉出風口,出風口可以調節出風的方向。然后再從頂部的回風口出風進行循環。一般房間不是很大的老化房采用離心風機主。

The centrifugal fan is installed on the top of the aging room, and then the corresponding number of air ducts is designed according to the power of the fan and the size of the room. Each air duct is connected to the bottom of the room. Two double-layer louver outlets are installed on each air duct. The outlet can adjust the direction of the air outlet. Then the air is circulated from the top return air outlet. Centrifugal fans are used in ageing rooms which are not very large in general.

風柜主要是老化房的房間太大,跨度過寬,溫度均勻度要求過高,如果房間很大的話用離心風機數量相應增加,噪音將會很大。此造價成本很高,

The main reason is that the rooms of aging rooms are too big, the span is too wide, and the temperature uniformity is too high. If the rooms are large, the number of centrifugal fans will increase correspondingly, and the noise will be very large. The cost is very high.

2:溫度范圍(溫度范圍不同選用材料不同)

2: Temperature range (different materials used for different temperature range)

通常做老化房的材料有2種;EPS 彩鋼板和巖棉彩鋼板。

Usually there are two kinds of materials for aging room: EPS color steel plate and rock wool color steel plate.

EPS彩鋼板主要用于常溫到60度范圍的老化,EPS彩鋼板俗稱泡沫板,不阻燃,它不符合《建筑材料燃燒性能分級》B2級的規定,在60度以下長期使用沒有問題,

EPS color steel plate is mainly used for aging at room temperature to 60 degrees. EPS color steel plate, commonly known as foam board, is not flame retardant. It does not meet the requirements of grade B2 of building materials combustion performance classification. It has no problem in long term usage below 60 degrees.

巖棉彩鋼板是在老化溫度為60度以上,它阻燃,符合《建筑材料燃燒性能分級》A級的規定

Rockwool coloured steel sheet is flame retardant at ageing temperature above 60 degrees, which meets the requirements of Class A of Combustion Performance Classification of Building Materials.

另外市面上還有一種聚氨酯彩鋼板,它的最高耐溫為85度,可燃,如果燃燒的話有有害氣體產生,只有專業的公司才采用此材料,并且造價又貴。

In addition, there is also a polyurethane color steel plate on the market, its maximum temperature resistance is 85 degrees, flammable, if burned, there are harmful gases generated, only professional companies use this material, and the cost is expensive.

3:需要老化的產品以及產品功率(產品的不同涉及到產品是否發熱,功率涉及到里面供電的配置)

3: The products that need to be aged and the power of the products (the difference of the products involves whether the products are heated or not, and the power involves the configuration of the power supply inside).

老化產品的功率:在老化房內,要給產品的老化架供電,功率涉及到線材的大小和數量,如果產品發熱涉及到線材采用民用或軍用線材。

Power of ageing products: In the ageing room, power should be supplied to the ageing frame of the products. Power involves the size and quantity of wire rods. If the heating of the products involves the use of civil or military wire rods.

4:溫度均勻度要求

4: Temperature Uniformity Requirements

老化房的溫度一般40度的時候±1℃,50的時候±3℃,60℃

The temperature of ageing room is generally 40 degrees, 1 degree, 50 degree, 3 degree and 60 degree.

以上為±5℃,如果60℃以上均勻度要求過高的話可以采用PLC實行多點控制或是以子母機的方式來控制。

If the uniformity of above 60 C is too high, it can be controlled by PLC or by the way of parent computer.

5:常做老化的溫度點和產品的總功率(涉及到排風系統,排風是根據房間大小溫度范圍和產品的功率來恒定在謀個溫度點,當產品發熱過高的時候排風機運轉保證溫度控制在設定的溫度)

5: Frequently aging temperature point and total power of products (related to exhaust system, exhaust air is based on the size of the room temperature range and the power of the product to find a constant temperature point, when the product heating is too high, exhaust fan operation guarantees that the temperature is controlled at the set temperature)

二:老化房的做法

Second: The Practice of Aging Housing

第一種:用石膏板隔個房間,里面加一個東北那邊家庭里冬天的取暖裝置或是其他的加熱裝置,然后在頂上或是墻上裝幾個風扇,這種老化房造價低廉,安全系數不高,主要體現是溫度的造成局部地方過熱

The first one is to use gypsum board to separate a room with a winter heating device or other heating device in the north-east side of the family, and then install several fans on the top or on the wall. This kind of aging house has low cost and low safety factor, which is mainly reflected in the local overheating caused by temperature.

第二種:根據溫度的不同采用不同的隔熱板(主要有泡沫板、巖棉板)隔一個房間,然后在頂上根據房間的大小裝相應的軸流風機或圓筒風扇,然后裝上相應的風管,采用所謂的頂部吹風,頂部回風的概念,此老化房的造價比第一種稍微高點,但是違背熱風原理,并且如果房間稍微大點的話噪音非常大,均勻度不高。

Second: according to the temperature difference, use different heat insulation boards (mainly foam board and rock wool board) to separate a room, then install the corresponding axial fan or cylinder fan on the top according to the size of the room, and then install the corresponding wind pipe. The concept of top blowing and top return air is adopted. The cost of the aging house is slightly higher than that of the first type, but contrary to the principle of hot air. And if the room is a little bigger, the noise is very big and the evenness is not high.

第三種:根據溫度的不同采用不同的隔熱板(主要有泡沫板、巖棉板)以及板材的不同厚度隔一個房間,然后根據溫度的均勻度,老化產品的負載,房間的大小選擇相應的風機、風管的制作大小、加熱管的定制,根據熱氣往上的原理采用底部出風上面回風,然后根據房間的大小,均勻度的要求通過PLC實行多個溫度點控制,此老化房造價比較高,需要技術實力和經驗。此老化房安全系數高

Third: according to the temperature difference, use different insulation boards (mainly foam board, rock wool board) and different thickness of the board to separate a room. Then according to the uniformity of the temperature, the load of the aging product, the size of the room, choose the appropriate size of the fan, the production of the wind pipe, and customize the heating pipe. According to the size and uniformity of the room, PLC is used to control multiple temperature points. The cost of this aging room is relatively high, which requires technical strength and experience. This aging room has a high safety factor.

第四種:燒機房,隔離室的,人不用進去房間上卸產品,此造價昂貴。

Fourth kind: burning machine room, isolation room, people do not have to go into the room unloading products, this cost is expensive.

辛苦整理!轉載請注明來自 http://www.hvbdp.club/show.asp?id=130

推薦資訊

138-6181-2138
太空漫游 书